Seachem PhosGuard rapidly removes phosphate and silicate from marine and freshwater aquaria. It is not recommended for phosphate buffered freshwater. PhosGuard is highly porous for high capacity and bead-shaped for optimum water flow. It outperforms all competing products.
Why it's different:
PhosGuard is spherical. Its shape allows for maximum water flow through the media. Granular phosphate removers can become compacted, dramatically limiting their capacity to remove phosphate. If the media cant come into contact with the water, it cant remove phosphate from it. PhosGuard is the only spherical phosphate remover on the market. ***Aluminum Oxide IS NOT REGENERABLE. No matter what anyone tells you, baking an aluminum oxide media does not restore its capacity to remove phosphate. This misconception comes from the products original intended use: industrial air drying. Obviously, if a product absorbs moisture, the best way to remove that moisture is to bake it out. However, that only removes the water, not the contaminants contained in that water.***
Aluminium Oxide, Soluble Aluminium, and Coral Toxicity:
In recent years, there has been speculation that aluminum oxide based phosphate removers like PhosGuard release aluminum into the water and subsequently damage corals. The evidence to support this claim was largely anecdotal.
So, through a series of controlled experiments in both freshwater and saltwater, we intended to address both the question of aluminum solubility and aluminum toxicity. The results of these experiments show that under reef conditions (pH near 8) there is no detectable soluble aluminum released from alumina. Under conditions of low pH and high dosage levels, soluble aluminum can be released from alumina; at three times the label dosage rate, we detected 0.2 mg/L aluminum at a pH of 5.3.
Additionally, aluminum oxide is not easily absorbed into the cell to cause negative reactions. Even at three times the dose of PhosGuard, soft-bodied corals such as Sarcophyton remain unaffected.
For best results, PhosGuard should be placed so as to maximize the flow of water through it. It may be used in a canister filter, box filter, or any high flow area of a trickle filter. In some situations it may be necessary to use in a filter bag. Use 250 mL (~1 cup) for every 300 L (75 gallons*). Leave product in place for 4 days, then test phosphate or silicate concentrations with either MultiTest: Phosphate or MultiTest: Silicate. If the concentration of the component you are trying to decrease has not dropped to around 0.02 mg/L, then replace the PhosGuard, otherwise leave in place until levels begin to climb again. As long as concentrations remain under control, the product is not exhausted. Each 500 mL of PhosGuard treats over 600 L (150 gallons*) (i.e. will remove up to 30 mg/L phosphate in 600 L (150 gallons*) of water, depending on the initial phosphate/silicate concentrations and the current biological load. Over treating is not recommended. PhosGuard is not an exchange resin, it does not release anything into the water. It does not leach phosphate or silicate back into the water and may be removed, dried, and returned to service until exhausted. Continuous use of small quantities is better than intermittent use of larger quantities.
May generate heat on initial contact with water. Pre-wet by adding to a double volume of freshwater (e.g. 250 mL of product in 500 mL water), followed by a rinse.
Aquacadabra acts as credit broker/intermediary and not as a lender. Credit products are provided exclusively by Klarna Bank AB, which is authorised and regulated by the Swedish Financial Services Authority, with limited supervision by the Financial Conduct Authority.
Who should my customers contact if they have questions?
All existing customer loans have been automatically transferred to Klarna and your customers have also been notified directly. There will be no changes to existing terms and conditions and customers do not have to take any action. From 1st January 2019 Klarna became the lender on all new loan applications.
Should your customers contact you regarding any questions they may have, please ask them to visit: https://www.klarna.com/uk/CBRF or, if they have any other servicing needs about their loan agreement they can call us on 0333 321 6080.
Delivery & Returns
We really want you to be happy with the product that you've received. If however, when the goods arrive they're not what you want, then no problem - we have a 60 day no quibble return guarantee. Just let us know that you're going to return the item(s) by contacting us (stating your Order Number) and complete the returns packing slip that will have been included with your delivery. This will help us to quickly identify the item that you have returned (unopened and unused) - and we'll put a refund through for you.